Skip to content

Cylinder volume calculator (litres and m³)

A cylinder volume calculator needs the radius, yet most people measure the diameter. Pick whichever you have from the list and the tool does the halving.

What you enter stays on this device.

The volume of a cylinder is π times the radius squared times the height (V = π × r² × h), so a drum 60 cm across and 90 cm tall holds about 254 litres.

Cylinder showing its radius r and height h, with the formula V = π × r² × h: a drum 60 cm across and 90 cm high holds about 254 litres.

Worked example: how many litres in a tank 1 m across?

Take a water tank with an internal diameter of 1 m, standing 1.2 m tall. The volume of a cylinder is the area of its base times its height:

V = π × r² × h

  1. The radius is half the diameter, so 0.5 m.
  2. Area of the base: π × 0.5² ≈ 0.785 m².
  3. Times the height: 0.785 × 1.2 ≈ 0.942 m³.
  4. A cubic metre is 1,000 litres, so the tank holds about 942 litres.

Measure the inside. At 96 cm rather than 1 m, the same tank drops to 869 litres, 74 fewer, which is roughly what a thick wall takes away.

Three mistakes that throw the answer off

Using the diameter as the radius. The radius is squared, so the slip doesn't double the volume, it quadruples it. Our tank would jump to 3,770 litres.

Mixing units. A diameter jotted down in centimetres (50) and a height in metres (1.2) give 2.36 litres if you leave both on “cm”. Enter 50 and 120 cm and you get the right figure, 235.62 litres.

The final conversion. 1 m³ is 1,000 litres, 1 dm³ is one litre and it takes 1,000 cm³ to fill a litre. For inches, gallons or cubic feet, the unit conversion table saves you from slipping a decimal place.

Volumes of common cylinders

Internal diameters, rounded to the nearest centilitre.

Inside diameterHeightVolume
7 cm (a glass)10 cm0.38 L
30 cm (a bucket)30 cm21.21 L
60 cm90 cm254.47 L
1 m1.2 m942.48 L
1.2 m2 m2,261.95 L
2 m2 m6,283.19 L

How much water sits in a hosepipe?

A pipe is simply a cylinder on its side, with the length standing in for the height. 25 m of hosepipe with a 20 mm bore holds about 7.85 litres, which is worth draining before the first frost.

Inside diameterLitres per metre
16 mm0.201 L
20 mm0.314 L
26 mm0.531 L
32 mm0.804 L
40 mm1.257 L
50 mm1.963 L
100 mm7.854 L

Surface area: paint, labels, lagging

SurfaceFormula
The base or the lid (a circle)π × r²
The side wall only (curved surface)2 × π × r × h
Wall, base and lid (total surface)2 × π × r × (r + h)

On the example tank, the side wall comes to about 3.77 m², or 5.34 m² with the base and lid. A label or a lagging jacket only covers the wall: unrolled, it is a rectangle 1.2 m high and 3.14 m long (the circumference, 2πr).

For a room, a raised bed or a pond with straight sides, the cubic metre calculator is a better fit, and the square metre calculator will do for a floor.

Method and sources

References used:

This tool is checked by automated tests against known cases. Spotted a mistake? Report it on the contact page.

Last updated

Frequently asked questions

I only have the diameter. What now?
Choose “Diameter” under “Known measurement” and the tool halves it.
How many litres in 1 m³?
1,000 litres. And since 1 litre = 1 dm³ = 1,000 cm³, a cylinder of 6,283 cm³ holds 6.28 litres.
How tall does a 100-litre tank 50 cm across need to be?
About 51 cm. Divide the volume by the area of the base: 0.1 m³ ÷ (π × 0.25²) ≈ 0.51 m. Allow a little extra if it shouldn't be filled to the brim.
Curved or total surface area: which one do I need?
Curved (2πrh) for the side wall alone, as for a label or an open-ended tube. Total, 2πr(r + h), when the base and lid need painting too.
What about the volume of material in a tube?
Work out two cylinders of the same length, one with the outside diameter and one with the inside diameter. The difference is the volume of the wall; multiply it by the density of the material to get the weight.
Should I measure inside or outside?
Inside, whenever capacity is the question. On a tank 1.2 m tall, 96 cm across instead of 1 m means about 74 litres less.
Is a horizontal tank filled to half its height half full?
Yes, at exactly half height, because a circle is symmetrical. At any other level the depth doesn't give a simple share of the volume, and this tool doesn't cover that calculation.